Instalar el Programador de PIC K150 en Windows 10 (funciona para todas las versiones de Windows)Link para bajar el Software y Driver:https://laborjag.com/venta/arduino/pic-k150-icsp-programmer. The PIC K150 programmer drivers and software for use with Windows XP 32bit are available to download: Download. Drivers' folder to install the driver. PIC K150 ICSP PROGRAMMER. 8 pin 40 pin-board Allows programming of PIC device whilst in circuit via its ICSP and included cable. I am very new to PIC programming. I decided to buy a very cheap programmer, as the description implied that it would come with a software to.
Example ICSP (development board not included)K150 Programmer
Product DescriptionK150 is a low-cost high-performance PIC programmer, supporting many popular PIC chips. Allows reading, writing, encryption, and uses high-speed USB communication for fast programming ( speed average PICSTART + 3-5 times ). Fully automatic programming checksum ; equipped with 40pin DIP programming ZIF socket, direct programming of 8pin-40pinDIP chip; 8pin-40 pin chip as well as via the onboard the ICSP interface. Popular download software available; software-compatible the Windows98 and Windows2000/NT, Windows XP/windows7 operating system. Socketed chips for easy replacement and upgrade.
Please also check out our quick start guide to using the Great Cow Basic IDE with this programmer here:
http://forum.hobbycomponents.com/viewto .. 106&t=1688
Order Yours Here.
Features:
Support many popular PIC chips, programming, read, encryption and other features!
No external power supply required, communication and power by supplied USB cable.
Much faster programming rate than PICSTARTPLUS .
Can easily read the contents of the chip program area.
With 40pin ZIF socket, 8-pin to 40 pin PIC microcontroller chip can easily be programmed.
8 pin 40 pin-board Allows programming of PIC device whilst in circuit via its ICSP and included cable.
Compatible with Windows98 and Windows2000/NT, Windows XP / Windows 7 and other operating systems.
PLEASE NOTE THAT THIS PROGRAMMER IS NOT CURRENTLY COMPATIBLE WITH WINDOWS 8.x and above
UPDATE: For Windows 8/8.1/10 users we have a tested and working driver. However this is an unofficial driver version and although we have tested and confirmed it to work a a Windows 10 system we provide no warranties or guarantees that it will work with your system. The driver can be found towards the bottom of this post. We value your feedback on this fixed driver.
Package Includes:
1x K150 Pic Programmer
1x USB Cable
1x ICSP Cable
Windows software:
Windows Drivers:
Windows drivers for windows XP/7 can be downloaded here.
An unofficial driver version (please see note at the top of this post before installing) for Windows versions 8, 8.1, and 10 can be downloaded directly from our forum here:
Quick setup guide:
1) Download and install the appropriate driver then attach the K150 programmer.
2) Download the PIC Program Software English Version.zip zip file to your computer and then unzip it.
3) Inside the unzipped folder you will see the microbrn software called microbrn.exe. Double click this and the microbrn programming software should open up.
4) Set the COM port for your K150 programmer by going to File->Port and enter the COM port number in the window that opens up (you can find the COM port number from windows file manager).
5) Make sure that the correct programmer type is selected by going to File->Programmer and selecting K150
6) From the main window select your PIC device from the Chip Selector drop down selection. Microbrn should then show you where on the ZIF socket (or ICSP header) you should place your PIC.
7) Next load in your hex file by going to File->load
8) Finally you can upload your hex file to your PIC device by clicking the program button int he main window.
Note that if your hex file doesn't contain fuse settings you can set them by clicking the Fuses button before uploading to your PIC
Known issues and solutions:
When attempting to program the EEPROM of my device I get a reset error and the programmer fails to program the device.
This is caused by an incorrect setting in the Pic programming software's configuration file. To fix this problem locate the file named ‘chipdata.cid’ which should be in the same folder as your microbrn software. Edit this file with a text editor and locate the setting's for your particular device. Amongst these settings you will find a value for ProgramDelay. Keep increasing this value by 10 until you are able to program your device's EEPROM. Please note that you will need to restart the software each time you edit this file.
The microrn software keeps saying I have the wrong COM port
This problem is normally caused because the microbrn software doesn't like high COM port numbers. If the COM port of your programmer is above COM9 you can lower it by doing the following:
Make sure the programmer is plugged in.
In windows open up device manager (click start and type dev man in the search box)
Find the COM port for the programmer under Port (COM & LPT)
Right click on it and select properties
In the window that opens click the Port Settings tab
Click the Advanced button
In the COM port number drop down box change the COM port number to a lower value
They will probably all say they are 'in use' but so long as you don't have any hardware attached that is currently using that particular COM port it's fine to choose it.
Click OK to close the two windows and then close device manager.
Unplug the programmer and reattach it.
Then restart microbrn.
I am using Windows 8/10 and I can't get the programming software to talk to the programmer. What am I doing wrong?
Currently the K150 does not work with Windows versions above Windows 7. This is due to the fact the latest versions of the Prolific USB driver no longer support the PL2303-HX version of the USB interface chip that is installed on the K150. Whereas installing an older version of the driver would normally resolve this issue, unfortunately Windows versions 8 and above will immediately update the driver to the latest and incompatible version without any notification. At the moment we not aware of a workaround for this issue however we will update this post should we find one. Update: Please see the note found at the top of this post for a solution.
K150 Pic Programmer Driver Windows 8 64 Bit
Disclaimer: Libraries, example code, and diagrams are provided as an additional free service by Hobby Components and are not sold as part of this product. We do not provide any guarantees or warranties as to their accuracy or fitness for purpose.
Descriptions and diagrams on this page are copyright Hobby Components Ltd and may not be reproduced without permission.
Instalar el Programador de PIC K150 en Windows 10
(funciona para todas las versiones de Windows)
Link para bajar el Software y Driver:
https://laborjag.com/venta/arduino/pic-k150-icsp-programmer/
If you already tried and you had problems, I recommend you to see my previous video:
Si ya intentaste instalarlo y tuviste problemas, te recomiendo ver mi anterior video:
https://www.youtube.com/watch?v=RDdpByMeOPI
For more reference:
http://www.kitsrus.com/pic.html
THANK YOU! Your visit to this video fills me with joy and desire to continue to create more content, if you like click in 'I Like' and remember to SUBSCRIBE to stay abreast of every new video.
-----------------------------------------------------------------------------------------------------------
MUCHAS GRACIAS! Tu visita a este video me llena de alegría y ganas de seguir creando más contenido, si te gustó presiona 'Me Gusta' y recuerda SUSCRIBIRTE para estar al tanto de cada video nuevo.
Copyright 2017 By Luis Borja
https://laborjag.com
وقت التشغيل 00:05:56
Borja, Colima, Gadget, Install, PIC, PICs, Programmer, Microcontroller, K150, K140, Windows, Windows 10, Windows 8, Windows 7, Vista, PC, ICSP, 16F877A, Fuse, How, 10 Series, 12C series, 12F series, 16C series, 16F series, 18 Series, Pic K150 ICSP Programmer, Tutorial, driver, sotware, Prolific, Kitsrus, Atmel, K128, K182, DIY, USB, Flash, AVR, Fixit, Fix, Test, grabador, 16F628A, Asc timetable download for mac.